![[PLT3050B] USB3.0 Production Line Tester](http://litektw.com/uploads/tadgallery/small/2013_04_10/142_s_PLT3050B_USB3.0-Production-Line-Tester.JPG "[PLT3050B] USB3.0 Production Line Tester")
![[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/97_s_HDMI-CR02AM_HDMI-Active-TypeC-Recpetacle-TF.jpg "[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture")
![[LT-SATA1.0] SATA Standard Fixture Set](http://litektw.com/uploads/tadgallery/small/2011_11_21/39_s_SATA-Standard-Fixture-Set.jpg "[LT-SATA1.0] SATA Standard Fixture Set")
![[DP-01ARM] DisplayPort Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/103_s_DP-01ARM_DP-Receptacle-TF.jpg "[DP-01ARM] DisplayPort Receptacle Fixture")
![[PLT2050D] HDMI Production Tester](http://litektw.com/uploads/tadgallery/small/2009_03_06/47_s_PLT2050D_HDMI-ProductionLine-Tester.jpg "[PLT2050D] HDMI Production Tester")
![[HDMI-CP01A] HDMI1.4 Type C Plug with Power Fixture](http://litektw.com/uploads/tadgallery/small/2011_09_08/75_s_HDMI-CP01A_HDMI-TypeC-Plug-with-Power.JPG "[HDMI-CP01A] HDMI1.4 Type C Plug with Power Fixture")
![[HDMI-AP01AM] HDMI1.4 Type A Plug Fixture for Tektronix](http://litektw.com/uploads/tadgallery/small/2012_04_05/96_s_HDMI-AP01AM_HDMI-TypeA-Plug-TF-ForTektronix.jpg "[HDMI-AP01AM] HDMI1.4 Type A Plug Fixture for Tektronix")
![[MDP-02APM] Mini DP Plug 15G Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/105_s_MDP-02APM_MiniDP-Plug-15G-TF.jpg "[MDP-02APM] Mini DP Plug 15G Fixture")
![[MHL-CK01AM] MHL Calibration Kit Fixture](http://litektw.com/uploads/tadgallery/small/2011_07_25/31_s_MHL-CK01AM_MHL-Calibration-Kit-TF.JPG "[MHL-CK01AM] MHL Calibration Kit Fixture")
USB2/3/4
Introduction
Most of the interfaces are designed by differential 100 ohms system, just like SATA, SAS, Lan, Infiniband, DVI, HDMI, SFP.. etc. The bandwidth of these interfaces is wide up to 20GHz or more. In this way, a good test fixture (Jig) for testing the raw cable with multi-AWG range becomes very important.
LiTek engineering team devoted 2 years and studied the features of raw cable. Now, LT-100R-20G is suitable for this application.
The LT-100R-20G can be used with many instruments as well as TDR, NA and Pulse Generator ..etc. A engineer can easily inspect the cable performance instead of after assembly.
Introduction
Most of the interfaces are designed by differential 100 ohms system, just like SATA, SAS, Lan, Infiniband, DVI, HDMI, SFP.. etc. The bandwidth of these interfaces is wide up to 10GHz or more. In this way, a good test fixture (Jig) for testing the raw cable with multi-AWG range becomes very important.
LiTek engineering team devoted 2 years and studied the features of raw cable. Now, LT-100R-4A is suitable for this application.
The LT-100R-4A can be used with many instruments as well as TDR, NA and Pulse Generator ..etc. A engineer can easily inspect the cable performance instead of after assembly.
Introduction
Most of the interfaces are designed by differential 100 ohms system, just like SATA, SAS, Lan, Infiniband, DVI, HDMI, SFP.. etc. The bandwidth of these interfaces is wide up to 20GHz or more. In this way, a good test fixture (Jig) for testing the raw cable with multi-AWG range becomes very important.
Introduction
LiTek's DPA-12B is a good probe test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPA-12B probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
Introduction
LiTek's DPA-12 is a good probe test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPA-12 probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
Introduction
LiTek's DPR-12B is a good receptacle-end test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPR-12B probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
