![[USB3-AP01A] USB3.0 Type A Plug Fixture](http://litektw.com/uploads/tadgallery/small/2011_08_03/63_s_USB3-AP01A_USB3-TypeA-Plug.jpg "[USB3-AP01A] USB3.0 Type A Plug Fixture")
![[USB3-AR01A] USB3.0 Type A Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2011_09_27/17_s_USB3-AR01A_USB3-TypeA-Receptacle.jpg "[USB3-AR01A] USB3.0 Type A Receptacle Fixture")
![[MDP-02ARM] Mini DP Receptacle 15G Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/104_s_MDP-02ARM_MiniDP-Receptacle-15G-TF.jpg "[MDP-02ARM] Mini DP Receptacle 15G Fixture")
![[HDMI-AR02AM] HDMI1.4 Type A Receptacle with Power Fixture](http://litektw.com/uploads/tadgallery/small/2011_12_14/84_s_HDMI-AR02AM_HDMI-Active-TypeA-Rec-TF.jpg "[HDMI-AR02AM] HDMI1.4 Type A Receptacle with Power Fixture")
![[SFP-P01AR] SFP+ Plug Fixture](http://litektw.com/uploads/tadgallery/small/2012_10_08/137_s_SFP-P01AR_SFP-Plus-Plug-Fixture.jpg "[SFP-P01AR] SFP+ Plug Fixture")
![[QSFP-R07BR] QSFP28 Rec Active Fixture](http://litektw.com/uploads/tadgallery/small/2017_07_20/156_s_qsfp.jpg "[QSFP-R07BR] QSFP28 Rec Active Fixture")
![[LT-SATA1.0] SATA Standard Fixture Set](http://litektw.com/uploads/tadgallery/small/2011_11_21/39_s_SATA-Standard-Fixture-Set.jpg "[LT-SATA1.0] SATA Standard Fixture Set")
![[DP-01ARM] DisplayPort Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/103_s_DP-01ARM_DP-Receptacle-TF.jpg "[DP-01ARM] DisplayPort Receptacle Fixture")
USB2/3/4
Introduction
Litek Technologies DisplayPort cable test solution provides you with a fast and easy way to verify your DisplayPort cable to meet DisplayPort Compliance Test Specification. This solution integrates both precision test fixture and TpNA software tested with Network Analyzer (NA) and Time Domain Reflectometry (TDR) and let engineers see the interaction between time and frequency domain.
The TpNA DisplayPort Engine can be easily used to control NA and TDR, following DisplayPort Compliance Test specification to test Return Loss , Insertion Loss , Near End Noise, Far End Noise, Power Sum FEN , Impedance and Skew automatically. It also outputs an Excel report file immediately that enables engineers to get a complete, fast and accurate test result and thus allowing quick troubleshooting and design.
Introduction
LiTek's DPA-12B is a good probe test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPA-12B probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
Introduction
LiTek's DPA-12 is a good probe test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPA-12 probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
Introduction
LiTek's DPR-12B is a good receptacle-end test fixture for Display-Port Source and Sink signal quality and protocol testing. Not only 4 Lane pairs, Aux Channel, but also all low frequencies signal pins had been extended to the SMA connectors and the 2.54-mm pitch connector.
Since the pin assignments are reversed in Source and Sink sides. DPR-12B probe test fixture is labeled with SLXX for Source end and with LLXX for Sink (Link) end.
1 
