![[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/98_s_HDMI-CR02AM_HDMI-Active-TypeC-Recpetacle-TF.jpg "[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture")
![[HDMI-DP01A] HDMI1.4 Type D Plug with Power Fixture](http://litektw.com/uploads/tadgallery/small/2011_09_08/16_s_HDMI-DP01A_HDMI1.4-TypeD-Plug-with-Power.JPG "[HDMI-DP01A] HDMI1.4 Type D Plug with Power Fixture")
![[DP-01ARM] DisplayPort Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/103_s_DP-01ARM_DP-Receptacle-TF.jpg "[DP-01ARM] DisplayPort Receptacle Fixture")
![[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/99_s_HDMI-CR02AM_HDMI-Active-TypeC-Recpetacle-TF.jpg "[HDMI-CR02AM] HDMI1.4 Active Type C Receptacle Fixture")
![[MDP-02APM] Mini DP Plug 15G Fixture](http://litektw.com/uploads/tadgallery/small/2012_04_05/105_s_MDP-02APM_MiniDP-Plug-15G-TF.jpg "[MDP-02APM] Mini DP Plug 15G Fixture")
USB2/3/4
Introduction
PLT3045A is a tester/programmer which is desiged to test/program HDMI active cable using Synerchip SC2031Q HDMI cable booster chip. The PLT3045A test the HDMI active cable Bit Error Rate (BER) from low bit rate up to 3.4Gbps, find an optimal setting for SC2031Q and program the cable using the optimal setting. The PLT3045A control software implement learning capability to select some best settings for certain type of cable and store the selected settings for later testing the same cable type. There are a lot of setting implemented in Synerchip SC2031Q cable booster to adapt to different cable loss. By the learning capability, the PLT3045A can save a lot of cable test time.
Introduction
PLT2050D (High Speed Transmission Analyzer) is a powerful online testing machine. Based on real TMDS Tx and Rx protocol and high performance image processor, it can be used to test DVI/HDMI cable assembly in very short time. By this way, you will increase the competitiveness to the market.
The TX transmitter encodes parallel data and serially transmits an input data stream over a T.M.D.S link (DVI / HDMI Assembly) to the RX receiver. Then PLT2050D compares the different between input Streams and Recovered Streams, and show the result on the LCD platform.
Introduction
LiTek's HDMI1.4 test fixture set could be used to measure Type A and Type C cables. Other type connectors are option here. By using TpNA for HDMI, we can measure the high frequency parameters soon.
From HDMI CTS1.4, we can directly measure TEST ID 5-3 TMDS Data Eye Diagram. We can also select other high frequency parameters as followings:
Introduction
LiTek's HDMI-DP01A is a HDMI Type D Plug test fixture used to measure HDMI connector of D plug or HDMI source with HDMI Type D receptacle connector and connected with HDMI D type cable assembly. There are 4 pairs with SMA connectors in the Scope or Signal generator sides. The impedance in the test fixture is well designed between 95~105 ohms. The intra pair skew for all 4 pairs are designed less than 3ps.
Introduction
LiTek's HDMI-DR01A is a HDMI Type D receptacle test fixture used to measure HDMI cable with Type D plugs and HDMI source with HDMI Type D receptacle connector and connected with HDMI D type cable assembly. There are 5 pairs with SMA connectors in the Scope or Signal generator sides. The impedance in the test fixture is well designed between 95~105 ohms. The intra pair skew for all 5 pairs are designed less than 3ps.
